IT / EN
Skip to Content
VICTRIX PRO 100 1 I
Code 3.024491
Heat output ref. 80-60°C kW 90,0
Heat output ref. 50-30°C kW 98,8
Efficiency at nominal heat output ref. 80-60 °C 97,5%
Efficiency at nominal heat output ref. 50-30 °C 107,0%
Dimensions (HxWxD) mm 1038 x 600 x 627
Modulating heat output 10 - 100%
Wall hung, modular condensing boiler for heating only.
90 kW heat output.
Wide modulating ratio up to 5 boilers in cascade installation, high performances with reduced consumption thanks to the 1:10 modulation range and high efficiency, the new VICTRIX PRO boiler is the ideal solution for light commercial solutions in residential and commercial buildings. The new design, compact and linear, with a vertical sliding door protecting the control board, makes its installation easy even in residential buildings (according to the current regulations in force in each country).
VICTRIX PRO can be used on the appropriate supporting modulation frame for floor standing installations. Certified for indoor and outdoor installations, even in unsheltered areas thanks to the IPX5D electric protection, the boiler is supplied with the -5 °C anti-freeze kit as standard.
Thanks to low emissions of carbon monoxide (CO) and nitrogen oxide (NOX), VICTRIX PRO 100 1 I belongs to class 5, the most environmentally-friendly class established by the European standards (UNI EN 297 e UNI EN 483).
Wide modulating heat output
Ideal for energy efficiency upgrade
Possible installation in cascade
Thermoregulation
Cascade and zone regulator kit       Code 3.015244
ON-OFF adjustment, modulation and malfunctions of the VICTRIX PRO in cascade (max 8). It can manage any climatic zone regulators in the system (max 3 plus 1 dedicated to the hot tap water circuit).
Wall box kit for cascade and zone regulator       Code 3.015265

If the cascade and zone regolator is not install inside an electrical box.

System delivery probe kit for the boiler VICTRIX PRO       Code 3.024245

Connected to the boiler board, it measures the delivery temperature after the hydraulic manifold.

Kit sonda esterna (for single installation)       Code 3.015266

Connected to the boiler board, it measures the delivery temperature after the hydraulic manifold.

Tele-management kit       Code 3.024244

Can be combined exclusively with the cascade and zone regulator for connection to an ethernet network or via router/modem to an ADSL line for connection to a remote system.

External probe (for installation in battery)       Code 3.024511

Connected to the cascade and zone regulator, it optimizes energy consumption by correcting the delivery temperature to the system for smooth temperature function

Flow probe       Code 3.015267

Positioned on the delivery pipe, after the hydraulic separator, it allows the cascade and zone regulator to control system temperature as well as that of any mixed zones.

CRONO 7 (weekly digital chronothermostat)       Code 3.021622

Available for all models.

Class of device IV* or VII
Contribution to the environmental heating seasonal energy efficiency 2%* or 3,5%

* as standard

CRONO 7 WIRELESS (wireless weekly digital chronothermostat)       Code 3.021624

Available for all models.

Class of device IV* or VII
Contribution to the environmental heating energy efficiency 2%* or 3,5%

* as standard

Zone manager kit       Code 3.015264

Electrically connected to cascade and zone regulator, serves to manage climatic conditions of one of system zone, and allow remote control of the cascade and zone regulator.

Modulating room thermostat       Code 3.015245

Electrically connected to cascade and zone regulator, serves to manage climatic conditions of one of system zone. Allows control of room temperature only.

Solar collector probe       Code 3.019374
To be used to manage the solar system coupled to thermal plants using the cascade and zone regulator.
Solar collector probe       Code 3.019374
To be used to manage the solar system coupled to thermal plants using the cascade and zone regulator.
Storage tank sensor kit (for managing the storage tank as a zone)       Code 3.015268

For the storage tank unit managed as a zone (with a circulator) and connected to the cascade regulator (without external 3-way valve). For solar installations managed with cascade and zone regulator two probes are necessary.

Flue systems

Terminal vertical outlet outdoor kit Ø 80       Code 3.024295

For VICTRIX PRO.

Horizontal kit Ø 80 (to discharge in the chimney)       Code 3.015254

For VICTRIX PRO.

Terminal horizontal outlet kit Ø 80 (to discharge horizontally)       Code 3.015255

For VICTRIX PRO.

Horizontal concentric kit Ø 80/125       Code 3.015242

For VICTRIX PRO.

Vertical concentric kit Ø 80/125       Code 3.015243

For VICTRIX PRO.

Terminal vertical outlet kit Ø 80       Code 3.015256

For condensing boiler < 35 kW.

Exhaust manifold kit 2 VICTRIX PRO 80/100/120 Ø 200 with flue lock       Code 3.024281

Cascade installation - "Green Series" exhaust manifolds.
With installations in central heating systems, using up to 5 units in the battery, in configuration open chamber fan assisted, Immergas supplies special exhaust manifolds in PP equipped with flue lock (mechanical shutters), to prevent backflow of combustion products through the other non-functioning boilers.
The system is modular: there is an exhaust manifold kit for two boilers and one for additional boilers.

Additional exhaust manifold kit VICTRIX PRO 80/100/120 Ø 200 with flue lock       Code 3.024282

Cascade installation - "Green Series" exhaust manifolds.
With installations in central heating systems, using up to 5 units in the battery, in configuration open chamber fan assisted, Immergas supplies special exhaust manifolds in PP equipped with flue lock (mechanical shutters), to prevent backflow of combustion products through the other non-functioning boilers.
The system is modular: there is an exhaust manifold kit for two boilers and one for additional boilers.

Additional exhaust manifold kit Ø 250 with flue lock for 4 VICTRIX PRO 100/120       Code 3.024666

Cascade installation - "Green Series" exhaust manifolds.
With installations in central heating systems, using up to 5 units in the battery, in configuration open chamber fan assisted, Immergas supplies special exhaust manifolds in PP equipped with flue lock (mechanical shutters), to prevent backflow of combustion products through the other non-functioning boilers.
The system is modular: there is an exhaust manifold kit for two boilers and one for additional boilers.

Additional exhaust manifold kit Ø 250 with flue lock for 5 VICTRIX PRO 100/120       Cod. 3.024667

Cascade installation - "Green Series" exhaust manifolds.
With installations in central heating systems, using up to 5 units in the battery, in configuration open chamber fan assisted, Immergas supplies special exhaust manifolds in PP equipped with flue lock (mechanical shutters), to prevent backflow of combustion products through the other non-functioning boilers.
The system is modular: there is an exhaust manifold kit for two boilers and one for additional boilers.

Extension pipe Ø 200 kit 0,5 m long for flue manifold       Code 3.024663
For installations in central heating systems with VICTRIX PRO.  
Extension pipe Ø 200 kit 1 m long for flue manifold       Code 3.024662
For installations in central heating systems with VICTRIX PRO.
Extension pipe Ø 250 kit 1 m long for flue manifold       Code 3.024668

For installations in central heating systems with VICTRIX PRO.

87° bend kit Ø 250 for flue manifold       Code 3.024670
For installations in central heating systems with VICTRIX PRO.
No. 2 45° bend kit Ø 200 for flue manifold       Code 3.024664

For installations in central heating systems with VICTRIX PRO.

Options
Safety kit single boiler VICTRIX PRO      Code 3.023949
The kit includes thermometer, thermometer holder, lock, thermostatwith manual reset, connection tap for pressure gauge, manual reset pressure switch, gas intercepting valve trap, expansion vessel connection and pressure switch for minimum pressure. Insulation as standard.
Three-way valve kit connection to a separate storage tank VICTRIX PRO      Code 3.023950
The kit includes the storage tank probe. The power supply is 230 Vac.
Insulation as standard.
Hydraulic manifold kit for VICTRIX PRO 80/100/120      Code 3.023952
Specially sized for large thermal systems with high water content. Equipped with sludge collection filter on the return pipe.
Insulation as standard
IPX4D protection box kit for single boiler safety kit VICTRIX PRO      Code 3.024028
Hydraulic manifold kit DN 100 for 2 VICTRIX PRO 80/100/120 in cascade      Code 3.023959
Kit to connect 2 VICTRIX PRO 80/100/120 in cascade installation; it includes a 2 way interception valve, a 3-way interception valve and a non-return valve for each generator.
Insulation as standard.
Hydraulic manifold kit DN 100 for additional VICTRIX PRO 80/100/120 in cascade      Code 3.023960
In combination with kit 3.023959 serves to connect from 3 to 5 VICTRIX PRO 80/100/120 boilers in cascade installation (one kit required for each additional boiler); includes a 2-way interception valve, a 3-way interception valve and a non-return valve.
Insulation as standard.
Safety kit DN 100 for VICTRIX PRO 80/100/120 in cascade      Code 3.023961
The kit includes thermometer, thermometer holder, lock, thermostat with manual reset, connection tap for pressure gauge, manual reset pressure switch, gas intercepting valve trap, expansion vessel connection and pressure switch for minimum pressure.
Insulation as standard.
IPX4D protection box kit for cascade safety kit      Code 3.024038
Hydraulic separator for 200 kW installations      Code 3.021377
Separator with G2 ½" threaded connectors.
Insulation as standard.
Hydraulic separator for 400 kW installations      Code 3.021378
Separator with G2 ½" threaded connectors on boiler side - DN 100 on system side.
Insulation as standard.
Hydraulic separator for 350 kW installations      Code 3.023965
Separator with threaded connectors - DN 100.
Insulation as standard.
Hydraulic separator for 600 kW installations      Code 3.023962
Separator with threaded connectors - DN 100.
Insulation as standard.
Condensate neutralizer kit for single installation VICTRIX PRO      Code 3.019857
Necessary to neutralize the acidity of the condensation. Inclusive of granulate.
Granulate for condensate neutralizer VICTRIX PRO      Code 3.019865
Extra granulate for condensation passivator kit code 3.019857.
Condensate neutralizer kit for cascade installation      Code 3.019464
Necessary to neutralize the acidity of the condensation.
Inclusive of granulate.
Thermoregulation
Flue systems
Options
Related products
VICTRIX PRO 120 1 I
Wall-hung modular condensing boiler for heating only

OPEN PRODUCT

VICTRIX PRO 80 1 I
Wall-hung modular condensing boiler for heating only

OPEN PRODUCT

 
LA MIGLIORE RETE DI ASSISTENZA IN ITALIA
 
 
CERCA IL CENTRO ASSISTENZA PIÙ VICINO
 
 
 
 
 
CONTACT US
 
 
 
CERCA AGENZIE DI VENDITA
 
 
 
LA APP PER I PROFESSIONISTI
 
 
 
FOLLOW US ON IMMERGAS ITALIA
 
CAIUS CLUB PROFESSIONAL
CAIUS CLUB PROFESSIONAL
 
SEI UN PRIVATO?
ACCEDI AL CAIUS FAMILY CLUB
 
QUALITY IN SERVICES
MADE IN ITALY
50 years of experience
OVER 6 MILLION BOILERS INSTALLED